CMP Endurance (SDSS-C)

The Endurance cable cleats are metallic cable cleats which have been designed, constructed, and tested in accordance with the International Standard IEC 61914: Cable cleats for electrical installations, to ensure the securing and retention of cables, without sustaining damage to the cables.

 

The range is fabricated from 316L stainless steel in 24 sizes from 17 – 128mm.

 

The top opening is designed to fit more cleats installed side by side, whilst three M10 fixing clearance holes within each base, allow the versatility of installing with either one M10 bolt or two M10 bolts. This enables installation of the Endurance to a variety of mounting surfaces.

 

The hinge of the Endurance opens fully, allowing cables to be easily placed within the cable cleat, before closing and securing via the mouth piece bolt.

 

Liners come as standard which help to restrain the cable(s) within vertical applications. Where thermal elongation of cables occurs, the liner also provides a layer of protection between the cable sheath and the cable cleat during normal operation. This additional layer protects the cable from chafing on any mounting surface due to differential movements such as those found in marine and offshore applications. The liners also assist in the extra protection of cable(s) in the event of short circuit fault conditions. The standard liners supplied are classified as Low Smoke and Fume Zero Halogen (LSF0H), Phosphorus-free.

 

FEATURES

• Third party certification to IEC 61914
• 316L stainless steel
• 17 – 128mm in 24 sizes for trefoil formation / application
• Short circuit rating of 140kA peak fault
• Operating temperature -60°C to +60°C
• Standard Polymer Liners are classified as Low Smoke and Fume Zero Halogen (LSF0H), Phosphorus-free
• Combined single (M10) or two bolt (M10) fixing design

Display more Display less
Product Features
Table Data
Downloads
Recommended Products
  • Categories
    Cable Cleats
  • Design Specification
    IEC 61914
  • Cable Type
    6.1.3 Composite SDSS-C - Standard Duty Stainless Steel
  • Material
    316L Stainless Steel with Standard Polymer Liner Standard Polymer Liners are classified as Low Smoke and Fume Zero Halogen (LSF0H), Phosphorus-free
  • Needle Flame Test
    Pass - 120 second flame application time IEC 61914 clause 10.0, 10.1, IEC 60695-11-5
  • Impact Resistance
    Pass - Very heavy IEC 61914 clause 6.3, 6.3.5, 9.2
ENDURANCE PART NO. CABLE Ø RANGE TAKE (mm) DIMENSIONS (mm) WEIGHT (g)
W H D P FIXING HOLE Ø
D1 D2
SDSSC-017021 17-21 78 88 54 25 2 x M10 1 x M10 337
SDSSC-019024 19-24 79 89 54 25 2 x M10 1 x M10 349
SDSSC-023028 23-28 79 96 54 25 2 x M10 1 x M10 353
SDSSC--027032 27-32 82 104 54 25 2 x M10 1 x M10 357
SDSSC-030035 30-35 84 110 54 25 2 x M10 1 x M10 367
SDSSC-033038 33-38 97 117 54 25 2 x M10 1 x M10 379
SDSSC-036042 36-42 113 123 54 50 2 x M10 1 x M10 444
SDSSC-040046 40-46 115 131 54 50 2 x M10 1 x M10 457
SDSSC-044050 44-50 117 139 54 50 2 x M10 1 x M10 472
SDSSC-048055 48-55 123 148 54 50 2 x M10 1 x M10 489
SDSSC-051058 51-58 127 154 54 50 2 x M10 1 x M10 503
SDSSC-055062 55-62 147 161 54 75 2 x M10 1 x M10 560
SDSSC-059066 59-66 151 169 54 75 2 x M10 1 x M10 573
SDSSC-063070 63-70 154 177 54 75 2 x M10 1 x M10 587
SDSSC-067074 67-74 157 184 54 75 2 x M10 1 x M10 602
SDSSC-071078 71-78 161 192 54 75 2 x M10 1 x M10 613
SDSSC-074082 74-82 191 199 54 75 2 x M10 1 x M10 687
SDSSC-077085 77-85 192 205 54 75 2 x M10 1 x M10 703
SDSSC-082088 82-88 193 210 54 75 2 x M10 1 x M10 711
SDSSC-088096 88-96 204 225 54 75 2 x M10 1 x M10 733
SDSSC-096103 96-103 217 239 54 75 2 x M10 1 x M10 755
SDSSC-103111 103-111 236 254 54 75 2 x M10 1 x M10 853
SDSSC-111119 111-119 250 269 54 75 2 x M10 1 x M10 884
SDSSC-119128 119-128 267 285 54 75 2 x M10 1 x M10 915
Data Sheets